Description
JB7200-7388H NON-SEAL CANNED MOTOR PUMP
Features
255 gallon/minute flow rate
280 foot maximum head
2-pole, max 29 hp motor power
-76 to 752°F (-60 to 400°C) temperature range
ANSI 300#
ASME B73.3
JB7200-7388H NON-SEAL CANNED MOTOR PUMP
JB7200-7388H NON-SEAL CANNED MOTOR PUMP
Features
255 gallon/minute flow rate
280 foot maximum head
2-pole, max 29 hp motor power
-76 to 752°F (-60 to 400°C) temperature range
ANSI 300#
ASME B73.3
Related products
-
JB734-902RF CENTRIFUGAL ELECTRIC PUMPS WITH INVERTER
JB734-902RF CENTRIFUGAL ELECTRIC PUMPS WITH INVERTER Rotation speed: 1450 - 2900 1/min. Operating range: From 1 to 470 m3/h with head up to 72 metres. Liquid temperature range: From -10 °C to +140 °C (MCE/C) From -10 °C to +80 °C (MCE/P) Pumped liquid: clean, free of solids and abrasives, non-viscous, non-aggressive, non-crystallised and chemically neutral, with properties similar to water. Installation: normally in horizontal or vertical position, provided that the Motor is always above the pump. Maximum ambient temperature: +40 °C. Maximum operating pressure: 16 bar - 1600 kPa (for DN 200 max 10 bar). Insulation class: F. Flanging: PN 16 DIN 2533. -
JB7386-TL724 SINGLE-IMPELLER CENTRIFUGAL PUMP
JB7386-TL724 SINGLE-IMPELLER CENTRIFUGAL PUMP Operating range: from 1,8 to 96 m3/h, with head up to 62 metres. Pumped liquid: clean, free of solids and abrasives, non-viscous, non aggressive, non-crystallised and chemically neutral, with properties similar to water. Liquid temperature range: K 20/41, K 30/70, K 30/100, K 36/100 K 12/200, K 36/200, K 40/200 : Remainder of the range: Maximum ambient temperature: +40°C Maximum operating pressure: from -15 °C to +110 °C Protection class: 7.5 kW : 8 bar (800 kPa) : 10 bar (1000 kPa) IP 44 (IP 55 for 2,2 - 3 - 4 - 5,5 - 7,5 - 9,2 - 11 kW motors) Protection class at the terminal board: IP 55 Insulation class: F Standard voltage: single-phase 220-240 V / 50 Hz three-phase 230-400 V / 50 Hz up to 4 kW included - 400 V ∆ 50 Hz from 5,5 kW Installation: horizontal or vertical position, provided that the motor is always above the pump. -
JB397T-7836 SERIES-PUMP
JB397T-7836 SERIES-PUMP Features 1425 gpm maximum flow 475 ft at 206 psi with water maximum head 100 HP maximum power 150lb RF flange connection C-PTFE or optional SiC-Z bearing SiC shaft GFR-PTFE casing gasket 150psig at 250ºF Enclosed impeller 3550 rpm speed Neodymium magnets -
JB745-BY662 HIGH PRESSURE HYDRO SEEDING PUMPS
JB745-BY662 HIGH PRESSURE HYDRO SEEDING PUMPS Features: Sand cast aluminum construction with cast iron wear parts EPDM/EPR mechanical seal, O-rings, and gaskets 3in or 4in NPT suction/discharge ports Available with Honda E-start gasoline engine Discharge ports rotate in 180° increments Low suction and high suction options available Maximum head: up to 202ft Maximum flow: up to 560 GPM
